program flow chart

The simulation shows that the algorithm is effective. Finally, Based on the Experimental platform, designed a set of information fusion locating system, and target calculation program flow chart.

最后，基于现有的实验平台设计了应用信息融合技术的移动机器人目标定位系统实现方案，及算法流程。

The features of microcomputer control system of type HDZ& 10B electronic beam welder and main functions to control the welding table system are introduced. The block diagram of the microcomputer control system and the welding control program flow chart are given.

介绍了HDZ&10B型电子束焊机微机控制系统的特点和控制焊接工作台方面的主要功能指标，给出了该微机控制系统的组成框图和焊接控制程序结构图。

At the same time, gives out software structure and program flow chart of general GPS receiver.

同时, 给出了普通接收机的软件结构和程序流程图.

The communication between PLC and upper computer and its program flow chart are designed also.

论文还对PLC与上位机的通信进行了研究，给出了程序流程图。

After that the auther discusses the program flow chart of the end-device and the ZigBee/ Gprs gateway.

给出了终端设备的程序流程和网关设备的程序流程。

The corresponding software design and the main program's flow chart are also presented the paper. "

同时对软件设计做了相应介绍,给出了主要程序的流程图.

The system's software design of the error analysis is analyzed and explained in detail on the program conceive, the software framework design, the software framework map and program flow chart.

从程序设想、软件结构设计、软件结构图和程序流程图诸方面对误差分析系统软件设计作了细致地分析和说明。

The flow chart of main program and interrupt subprogram of the time service device and the electronic clocks were presented in the system.

论文的软件编写采用C51，给出了授时器、电子时钟的主程序和中断子程序框图。

In the aspect of software design, according the functional requirements of each module, the paper design their own program flow chart, and then design the specific program for each module.

在软件设计方面，根据功能要求分别设计了它们各自的程序流程图并根据流程图进行具体的程序设计。

Hardware structure chart and main program flow chart are given in the thesis.

文中给出了硬件结构框图和主程序流程图.

A kind of PLC control of stepping motor was introduced, software design discussed, the program flow-chart given, and control characteristics analyzed.

提出了对步进电机进行控制的PLC控制方法，并对其PLC控制软件设计进行研究，给出PLC控制的程序流程图，分析了其控制特性。

Based on the research of embedded assembly program flow chart automatic building, the breakpoint setting and checking mechanism, virtual instrumentation mechanism based on the PC values are proposed.

该文在汇编嵌入式软件程序流程图自动生成的研究基础上，提出了以PC值为基准条件的断点设置、检测机制以及虚拟插桩机制。

The program flow chart and the PID algorithm flow chart are given.

并给出了实现PID调节的程序流程图。

Through analysis, the authors draw a cause and effect feedback chart to which the authors give flow diagram explanation. Besides, the authors work out the emulation program of industry sub pattern by using the special purpose language of systematic dynamics, DYNAMO language.

通过分析，绘制了工业子模型的因果反馈图，并进行了流图分析，据此采用系统动力学专用语言DYNAMO语言，编写工业子模型仿真程序。

The purpose of this paper is to discuss the automatic generation of program flow chart of assembly embed-ded software.

程序流程图的自动生成是软件结构分析及软件测试的基础。

Details of the wireless voice communication system communication protocol; given system initialization, the audio input and data transmission, data reception and audio output, frequency hopping and address transformation module program flow chart and the main code.

详述了无线语音通信系统的通信协议；给出系统初始化、音频输入和数据发送、数据接收和音频输出、跳频和地址变换模块的程序流程图和主要代码。

It gives system Program Flow Chart and Data Flow Diagram and Structured Design Diagram and UML modeling Diagram.

并给出了系统的流程图、数据流图、系统设计的结构图和UML图。